PLDT wifi/modem network help

Discussion in 'PLDT DSL' started by you_aint_2_fast, Nov 26, 2012.





  1. good day. patulong sana mga sir kasi pinalitan po ng pldt yung modem ko

    eto yung binigay sakin

    [​IMG]

    meron din ako spare netgear wgr614v6 router, ganito sya

    [​IMG]

    gusto ko sana iset-up sya na yung pldt wifi modem ko meron nakakabit na PC via ethernet cable tapos gumagana din yung wifi para sa ibang wifi device like laptop etc. nasa house 1 to

    tapos may maha akong ethernet cable papunta sa Netgear wifi router ko na meron din nakakabit na pc via ethernet cable tapos gumagana din wifi para sa wifi device like iphone etc. nasa house 2 to

    same network sila nakakabit lang sa PLDT isp pero yung 2 router ko (PLDT Prolink and Netgear)
    magkaiba sana ng SSID at password

    eto yung diagram sana ng setup

    [​IMG]

    nagsearch na ko sa net na kailangan ko daw disable yung dhcp sa netgear tapos lan port to lan port and connection ng 2 router (walang nakakabit sa wan). iba na din yung ipaddress ng netgear ko 192.168.1.2 na. yung prolink ko default nya 192.168.1.1

    nakakabrowse yung pc2 ko na connected sa netgear
    yung pc 1 ko nakakabrowse din na connected sa prolink
    yung wifi device ko hindi makabrowse at hindi din madetect yung wifi ko sa netgear
    yung wifi device ko nakakabrowse at nakakaconnect sa prolink

    napapasok ko settings ng prolink via adminpldt 1234567890
    napapasok ko din settings ng netgear via admin password

    thank you
     



  2. Marami options para i-configure yang diagram mo. Tama din nabasa mo. Yung NetGear router mo, gawin mo na lang Access point, disable mo DHCP niya. hayaan mo na lahat ng PC mo mag-obtain ng IP sa PLDT Prolink mo.
     



  3. yun nga yung ginawa ko bro. nagwork sya pero using ethernet cable lang. wala ako makita na wifi signal sa netgear
     



  4. check mo configuration ng wifi ng netgear baka disabled.
     



  5. i tried several times but i can't get thru my netgear

    here's what i did at first

    i connected my netgear router to my pc 2 via ethernet using ethernet cable at lan port and changed the ip address to 192.168.1.200 and disabled the dhcp on it

    [​IMG]

    i went to wireless settings but i cant click this one

    [​IMG]

    here's my netgear status before i plug in my ethernet cable from PLDT Prolink modem/router to lan port on my netgear router

    [​IMG]

    PLDT Prolink modem/router ip address: 192.168.1.1 (i can access this one)
    Netgear ip address: 192.168.1.200 (cannot be accessed anymore)
    wireless AP: OFF (can't turn on since i cant access my netgear anymore when i connect it the internet)
     



  6. can you post your PLDT Prolink configuration settings?
     
  7. josekym

    josekym Member




    Tried doing this?: http://kb.netgear.com/app/answers/d...-wgr614,-or-wgt624-routers-as-an-access-point

    You could also try updating the firmware on the NetGear first and configure it again as you did. Since the wired part works, I don't see why the wireless part shouldn't.

    Alternatively, you can connect in LAN-Internet mode (i.e. modem LAN cable connected to WAN port of the NetGear), and run the NetGear as another router.
     



  8. AND, make it sure that your SSID is visible.
     



  9. update:

    nag-update na ko ng netgear router version and tried lan-lan set-up with netgear dhcp off and ipaddress different from PLDT prolink netgear (main). gumana naman lahat including pc2 to netgear via ethernet cable and wifi devices to netgear. all of a sudden nawala yung wifi connection ko pero yung pc2 via ethernet cable to netgear lan ok naman. tried powercycle wala pa din yung wifi

    sinubukan ko naman yung lan-wan as suggested no josekym. dhcp on sa netgear with different ipaddress from PLDT prolink main. same issue. gumana lahat at first. pc2 to netgear vbia ethernet cable and wifi devices to netgear connection. tapos nawala na naman wifi pero pc2 lan connection ok naman

    parang yung wifi connection ang nagkakaprob sa setup ko. SSID ok naman, nagtry na ko channels 1 and 11 kasi ive read na dapat iba ang channel ng netgear ko sa main (PLDT prolink) ko which is gumagamit ng channel 6.

    tinanggal ko ulit yung set-up. balak ko nalang ibenta yung netgear ko para bumili ng repeater or access point
     
  10. josekym

    josekym Member




    Looks like yung WiFi side ng NetGear mo ang may problem talaga... If the warranty on it is expired, maybe you can open it up and check if it has physical damage on the inside, like leaking capacitors or burned/scorched components...
     



  11. di ako mabusisi sa ganun bro takot ako sa mga clips baka may mabali. may gumagawa ba nun dito?
     



  12. to double check lang, nakikita ko din na WiFi lang problem ng setup mo, yes, baka hardware problem na yan...if isolate mo yung netgear mo din try mo paganahin yung WiFi niya..
     
                                 

Share This Page